Rate this post

A device is used to secure an object.

A bench vise, B machine vise, C hand vise

Hand vise, bench vise, machine vise.

A vise or vice is a mechanical apparatus used to secure an object to allow work to be performed on it. There are two parallel jaws that are threaded in and out by a screw and lever.

A vise grip is a pair of lever-actuated locking pliers.

Types

[

edit

]

Face

[

edit

]

The woodworker ‘s face vise has wooden jaws.

A face vise is the standard woodworking vise and is attached to a workbench flush with its work surface. It ‘s jaws are made of wood or metal to avoid marring the work. A retractable dog may be used to hold work against a bench dog.

A woodworker ‘s vise uses a split nut that allows the screw to engage or disengage with a half turn of the handle. The process of adjustment is greatly accelerated when the jaw is moved in or out throughout its entire range of motion. There are common thread types.

There are either face vises attached to the front of the workbench near the left end of the long side, or end vises attached to the right side of the narrow end.

The engineer ‘s bench vise is made of cast iron.

The “ bench ” is a basic workshop grade.

An engineer ‘s vise, also known as a metalworking vise, is a tool used to cut metal. It holds metal when cutting or filing. Most of the time it is made of cast iron. The jaws can be engraved with serrated or diamond teeth. Soft jaw covers made of aluminum, copper, wood, or plastic can be used to protect delicate work. The jaw opening of an engineer ‘s vise is the same as its jaw width.

An engineer ‘s vise is bolted onto the top surface of a workbench, with the face of the fixed jaw just forward of its front edge. There is a small anvil on the back of the vise. The engineer ‘s vises have a base. Pot metal or a very low grade of iron are used in some engineer ‘s vises. A lot of homeowner ‘s bench vises have exposed screws.

Variants

[

edit

]

There is a combination.

edit

A combination-vise combines an engineer-style vise with a subsidiary set of curved jaws below the main. A base that is pivoted is standard.

A bench vise is secured to a board, table, or bench by a vise-type screw on its base. Rarely does it pivot.

A small vise with a base.

A vacuum-mounted vise is a small engineer ‘s vise secured by a base and used for very light duty work. No pivot.

Machine

[

edit

]

Machine vises are mounted on machines. A machine-type vise is built into the saw.

Pipe

[

edit

]

A pipe vise is used to hold pipes. The main styles are yoke and chain. The chain style secures the pipe by wrapping it within a chain designed to adjust to length by link, tightened by a cam lever, and the yoke uses a top-mounted screw to tighten the pipe between two fixed jaws.

Other

[

edit

]

There are hand vices.

Leg vise.

There are other kinds of vise.

  • There is a hand vise.
  • A more complex machine vise. It allows the placement of the work to be precise.
  • Cross vise, which can be adjusted using leadscrews in the X and Y axes, is useful if many holes need to be drilled in the same workpiece using a drill press. The table is compared.
  • The vise is off-center.
  • Two jaws close against a right angle.
  • The vise uses gauge blocks to set up an accurate angle.
  • A vise.
  • Diemakers ‘ vise.
  • The saw vise is used for sharpening.
  • A pin vise is a tool used to hold objects by one end.
  • The vise is for jewelers.
  • Fly tying vise is used to secure fishing hook.
  • Leg vise or post vise, which is attached to a bench but also supported from the ground so as to be stable under heavy use, is used by an auto body repairman or blacksmith.
  • A broom vise.
  • A triangle vise, also known as a splicing vise, has three jaws. It ‘s used to close cable and wire rope.
  • It is now referred to as a Fractal Vise, which is used to hold complex forms.

See also

[

edit

]

References

[

edit

]

Notes

[

edit

]

Citations

[

edit

]

Source: https://nhadep247.net
Category: Machine